Throwing a basic pot - Lakeside Pottery Tutorial

		Page 1
					1																										2																															3
Place clay on bat firmly with tip pointed down																					Tap to center with dry hands while wheel is turning slowly																														Get your hands wet
										4																							5																															6
																										Push clay forward as shown (plow forward).  Wheel speed - fast
Let the clay turn while wet hand and wet clay create slurry / slip
																																																						Sit close to the wheel & anchor your elbows tightly against body
										7
																																		8																															9
When clay complies (feels calm), squeeze clay and cone up
																																																							Both hands are touching and elbows are against body
																											Level top of cone with thumbs pressure
								10																												11
																																																																			12
Coning down - place left hand as in previous step securing elbow into body
																												Place right hand on top of cone while interlocking with left hand
																																																								Right hand pushes down. Left hand pushes forward. Wheel speed - fast.
										13																										14																																	15
Right hand touches only half of the top surface from center to edge.
																																																										Slow wheel a bit. Place thumbs in center and mark the center
																												Left hand smooths outer edge of clay with palm
								16
																														17																																							18
	Decisively, make a hole in center - both hands are touching each other
																																																										Pull clay out - both hands are touching each other and clay is wet
																												Leave enough clay for pot's bottom
						19
																																																																				21
																																	20
	Move clay evenly and keep constant distance from bottom for flat surface
																																																									Do not overhang clay . When finished pulling, let go gradually to stay in center
																										Smooth all unevenness. Make sure clay is not too dry
		Page 2
																																23																															24
					22
																									Apply constant pressure on bottom. Move slowly towards center. Wheel speed - medium
																																																					Take off extra clay
	If bottom too thick or uneven pass thumbs on bottom as shown
																																26																															27
								25
																									Raise the wall - squeeze clay w/ fingers using a sponge. Use fingers tips only. Hands touching
																																																					Note that the thumb is helping in squeezing clay
Compress bottom to avoid "S" cracks
																																																																		30
																																	29
								28
Contact clay with finger tips to avoid unnecessary friction																							The pull - squeeze and lift. Don't be afraid to be a bit aggressive. Clay needs to be wet
																																																								Smooth the rim at end of each pull
																																		32																																	33
								31
Second pull - stay on bottom until you get desired thickness
																																																								... to avoid too much friction and possible torquing
																							As the wall gets thinner, use less finger surface contact ....
																																		35																																36
								34
																																								Collar top portion of cylinder in and even the rim
																					Even cylinder's rim
	Even wall of cylinder
																																	38																																39
									37
																																																						Note that only finger tips are touching the pot
		Shaping - Push inside of cylinder out while outside hand gently supports clay																				Touch hands as soon as able for stability
									40																									41																																		42
																							Clean bottom with wooden tool. Sharpen Wooden tool every so often																																		Under cutting -Clear clay from bat for easy access to the cutting wire
Smooth rim with Chamois
							43
																																	44																																				45
	Clear as much clay as possible to minimize trimming effort later
																					Watch the angle of the wooden tool.																																					Hold the cutting wire as shown
			Page 3
								46																											47																																			48
Push the wire against the bat with thumbs or index fingers																						Run wire all the way through keeping it tight and straight																																					If throwing for practice, slice pot to view wall uniformity
								49
	Good luck! Lakeside Pottery																																																Save page to PDF
																												COPYRIGHT Lakeside Pottery LLC COPYRIGHT and linking policy details

---

Your input is greatly appreciated and will help in creating improved pottery tips. Thank you, Patty and Morty

Name:
Email:
Input

543 Newfield Avenue
Stamford, Connecticut 06905
Directions
Phone: 203-323-2222
Fax: 203-406-9999
studio@lakesidepottery.com